RIGHT-ANGLE SOLDERABLE PLUGS

RIGHT-ANGLE SOLDERABLE PLUGS

Source AC Power Cable
$259.00 USD Example Sold out Sale
Length

DESCRIPTION

Think power cables don't make a difference? Think again.

The Source AC Power Cable is a remarkable upgrade to the power supply of any amplifier or audio component.


Solid IGL™ copper conductors replace the only stranded conductors in the power delivery system.

Hot and neutral conductors are composed of four isolated cores each in a helical array around the earth conductor.

 

DESIGN

High-purity proprietary IGL copper conductors for distortion-free midrange and
high frequencies.


Solid-core conductors eliminate the negative effects of strand interaction on the AC signal.


100% shielding blocks noise and bleeds to ground.

CONNECTORS

The Source comes with standard with a Wattgate™ 320i IEC connector on the output side, and a Wattgate 5266i US Wall Plug. Both are cryogenically treated.

 

**For any other length or plug requirements please contact us for a custom quote**
SIS™ DIY Solderless Patch Kit
$7.95 USD Sold out Sale
Size

DESCRIPTION

The first and only Patented Solderless Patch cable system to legitimize the product category for both sound quality and reliability.

Evidence Audio introduces the perfect 1/4″ Phone plug for use with its award-winning Monorail signal cable.

The perfect combination of Monorail sound quality, the convenience to build and rebuild without solder, a compact cable and plug combination, and no signal failures in the middle of a song!

As used by David Gilmour, Noel Gallagher, Graham Coxton, Ed O’Brien, Josh Smith, Guthrie Govan, Andy Timmons, Guy Pratt, Steven Rothery, and many others.

 

DESIGN

Our Proprietary high-purity IGL copper conductors for distortion-free midrange and high frequencies.

The solid-core center conductor eliminates the negative effects of strand interaction on the audio signal.

20 awg conductor size keeps skin-effect distortions outside the audio spectrum while offering ample cross-sectional area.

Parallel-run shield provides 98% coverage with minimal crosstalk.

Coaxial geometry with low capacitance.

Carbon-loaded extrusion for protection from triboelectric noise.

 

CONNECTORS

 

The inside of the tip of the SIS plug is carefully machined to have “threads” of a precise size and pitch. These threads cut and re-shape the soft conductor of the Monorail cable when turned around it several times.

When you push the prepared cable into the SIS plug, the soft copper will find the hole. When you turn the plug 1 or 2 times the harder brass core of the plug will catch and cut into the copper conductor. When you feel this happen you put the cap in place and screw the SIS plug into the cap.

This action turns the soft copper deeper into the SIS core – Mashes the ground up against the SIS body to make ground contact (airtight as the copper is deformed inside pushing air from the connection). This seals the jacket at the exit tightly so that the cable will not come loose from the plug and the cap will not come loose from the plug body. When finished the tip/core connection with the Monorail is also air-tight and in many ways better than a soldered connection. If you unscrew the SIS plug and remove the Monorail cable you can see the soft copper has been shaped to meet with the SIS core.

 

 

ASSEMBLY INSTRUCTIONS

 

1) REMOVE the thin black (conductive) skin from around the white insulation. If it touches where the conductor needs to enter, you’ll create a complete short or partial short with weak signal.

2) Do not cut up your cable into short pieces before attaching the plugs. Instead attach the first plug to your long/entire supply of cable. Measure the length required to the other plug. Cut and attach the second plug to complete your cable. Rinse, repeat.

3) Wear rubber gloves to get a good grip and spare sore fingers when closing tight.

 

ASSEMBLY FOR THE RIGHT-ANGLE CONNECTORS

 

ASSEMBLY FOR THE STRAIGHT CONNECTORS: 

 

Push the cable into the plug and when you seat the core, rotate the plug about 10-12 full revolutions (straight plug only). This will simultaneously thread the copper core into the tip of the plug and screw the body of the plug onto the cable jacket. You only need the jacket to enter the plug a few millimeters.

ESP-RA™ PLUG DESCRIPTION

The ESP-RA™ is the first solderable 1/4" phone connector from Evidence Audio and designed (like all of our products) with the primary purpose to sound demonstrably better than anything in its class.

What class does it fall in?  Its compact size and angled format makes it especially suitable for use with smaller cables on pedalboards specifically. Cables with an outer diameter of 4 mm, or around 0.155".

The current flood of plugs used to solder patch cables for a guitar pedalboard typically use a steel nail or pot metal to conduct the audio signal. Ferrous. Magnetic. While these plugs are compact for pedalboards, they cut corners by using inferior metals to carry the sound. They offer greater affordability yet greatly reduced audio quality.

MATERIALS

The contact points of the ESP-RA™ are machined from a high-copper-content brass. Brass offers the appropriate hardness and strength required for a connector with very good conductivity to minimize distortions caused by the cable the plugs are used on.

PATENT-PENDING DESIGN

The form factor is akin to a "pancake" style plug, with a patent-pending closure system that allows for the plug to be assembled with one screw instead of two. This allows for a smaller form-factor as well as reduced assembly time. 

HOUSING SIZE

Width 16 mm | Height 25 mm | Depth 8 mm

CABLE COMPATIBILITY

To give an idea of the cables appropriately sized to work with the ESP-RA plug here's a list of some better known makes and models, which are all compatible:

Evidence Audio Blackrock, Evidence Audio Monorail, Belden 1865A, Belden 8218, Bill Lawrence BL-150, BPTA CA 0492, BPTA CA 0678 Canare GS-4,  Free the Tone CU-418, George L's155, Mogami 2314, Sommer SC-ONYX TYNEE

RECOMMENDED CABLES


View full details